the cnc workbench

Nothing between your designand the foam.

Roughing and finishing toolpaths computed from the exact surface and the exact tool you chose — previewed as the finish you will actually sand, gated by readiness checks, and post-processed for your machine. Every number in the program is a number you set.

3·4·5
axis toolpaths
±0.05
mm path accuracy
10
machine post families
6
blank-catalog regions
The workbench

Five tabs, machine to shop floor

The CNC mode is organized the way a job actually runs — commission the machine, pick the foam, dial the cutters, plan the operations, then run them. Everything below hangs off these five tabs.

shapestudio — cnc-workbench zoom
tab 011/05

Machine Bed

Commission once, reuse on every board.

  • Profile, axes & travel limits
  • Bed type: supports · clamps · table · mold
  • Datum, flips & calibration
tab 022/05

Blank

The foam you actually have.

  • Global catalog, ranked by waste
  • Auto blanks & block blanks
  • Material feeds per foam
tab 033/05

Tool Library

Shared across every document.

  • Cutters namespaced per machine
  • Tool-life accrual on export
  • Engrave bit behind a real tool change
tab 044/05

CAM Operations

The multi-op program, your rules.

  • Stringer · roughing · finishing · outline
  • Plugs, layers & engraving
  • Scallop or fixed line density
tab 055/05

Execution

From simulation to the shop floor.

  • Backplot, stock sim, collisions
  • Setup sheet & job queue
  • Operator mode & resume
the contract

The preview matches the toolpath, the toolpath matches the G-code, and the G-code matches the settings you chose. When something is off — a blank too small, a support under a pocket, a travel limit overrun — the readiness gate says so before the export button unlocks. And the first program for any new setup starts the way ours do: with the air-cut toggle on.

01/toolpaths

The multi-operation program

One file per side, built from named operations — STRINGER, ROUGHING, FINISHING, OUTLINE, PLUGS, 3D LAYERS, ENGRAVE — each framed by searchable comment banners with pass counts and resume IDs. You always know which block of the program you are reading.

Stringer strategy

Depth-stepped stringer cutting (three passes by default) with ghost cleanup paths, upward cut, zigzag, extension and hop options — plus an optional dedicated STRINGER ROUGH operation behind its own tool change.

Stepped-depth roughing

Coarse steps with a fine final skin (2.0 cm down to 0.5 cm by default), deck and bottom pass counts derived from the stock automatically or set by hand, follow-blank-outline and margin options.

Finishing: lines or scallop

Fixed line density (30 deck / 25 bottom / a 5-line rail band by default) or a target scallop height — 0.2 mm out of the box — with HD precision doubling and per-face line packing that narrows toward the rail.

  • 0.2 mm scallop default

The outline pass

Three passes freeing the rail from deck to bottom, climb or conventional, with a square-rail mode — and Outline Y Shift to deliberately leave a skin of foam for hand finishing.

Deck/bottom handoff

Split the work at the apex, the tuck, or tuck plus flat bottom — with angle caps per face so finishing stops where the rail goes near-vertical and the outline takes over.

Plugs & pockets

Fin boxes, leash, handle, footstrap and vent pockets — dug with the cutter or position-marked only; FCS II and Futures ring spacing follows the tool. Cut separately into their own file when you want.

3D layers as operations

Channels, concaves, vee and step decks cut as named LAYER operations with per-layer axis counts — the same displacement layers you sculpted in design.

Adaptive feeds

Rail speed zones, curve slowdown, stringer-cross factors per material, progressive curvature and corner ramping — one shared feed planner drives the simulation, the time estimates and the G-code, so they can never disagree.

Sequencing & leads

Side-to-side, concentric, concentric-plus-rail or one-side ordering, tail-first options, and lead-in/lead-out arcs per strategy.

Hotwire engine

For EPS and XPS: thermal calibration with burn-kerf correction, computed parabolic wire-sag compensation, synchronized or independent 4-axis motion, and separate profile/outline exports.

  • eps · xps

Mold making

Two-piece female cavity molds with block-stock readout, hotwire block-splitting G-code and templates, per-half cavity programs with Z0 at the parting face, and registration dowels by default.

Fin CNC & sheet nesting

A dedicated workbench for fins: tabletop 3-axis or 5-axis with per-point rotary tilt and non-TCP arm compensation, roughing, both foil sides, outline and screw holes, holding tabs — plus a nesting sheet for mixed fins, free-drag layout and auto bin-packing into one combined program.

02/verification

Verified before foam

Previews here are not decoration — each one is an audit. The scallop preview reproduces the toolpath’s real lateral line distribution, because the cusp you see is the cusp you will sand.

shapestudio — cnc zoom

Toolpath backplot & player

The full program drawn in 3D colored by feed speed, with a floating transport dock — scrub 0–100%, step 5%, 0.01× to 25× speed, and live X/Y/Z with FEED or RAPID readout.

Stock simulation

A dexel model of the blank milled in lockstep by the actual cutter profile — verdict CLEAN or GOUGES FOUND, with max gouge, rest material, rest volume in cm³ and the worst X/Y locations. A blank that cannot cover the design is caught here, not on the bed.

Collision detection

The tool holder is scanned in machine space across the whole program — colliding segments render magenta with a live count. Biased to over-warn; built to never miss.

Cutter reachability map

Where the chosen cutter physically cannot reach — tight concaves, channel corners, rail tucks — per face and per machine frame, with the unreachable percentage, the hand-finish area in cm², and the biggest tool that would still clear it.

The readiness badge

The gate over every export button: hard errors for a too-small blank, support conflicts, travel-limit overruns, a program on the wrong side of Z0, a stepover wider than the cutter. Warnings for the unset RPM. It turns green when the job is actually ready.

Verify G-code files

Backplot any external program — .nc, .ngc, .gcode, .tap, .eia — with G2/G3 helical arcs and G20/G21 auto-detection, audited against the design surface. Rapids are never judged; cuts are.

Hand-shaping map

A printable rest-material leave map: plan-view color bands, a twelve-station table of what is left in millimeters, and a 1:1 scale check bar for the printer.

Speed chart & slice preview

See where the program feeds fast and slow across the board — and a shaper’s-eye 2D cross-section with the tool contact point, rail profile and spindle clearance.

03/machine_&_setup

Your machine, charactered once

A machine profile is commissioned once and reused on every board — travel limits, axis signs, datum, calibration, tool library and post-processor, namespaced per machine and exportable as JSON.

shapestudio — setup.txt
APS 3000
3-axis · 4-axis disk
AkuShaper
disk · .nc
3DM / Precision
bullnose · .nc
Generic router
3 & 4-axis · Mach3 · GRBL · LinuxCNC
Thermwood CutCenter
.eia · inch
MultiCam
iso
HOMAG / Weinig
5-axis iso
Haas VF
5-axis · G20 · T1 M6 / G43
Shaper Origin
96 dpi svg contours
Custom
raw iso output

Four bed types

Supports (the shaper classic two-post), clamps, vacuum table, or a mold cavity — each one changes the margins, the collision checks and the support logic to match physical reality.

Envelope auditing

Travel limits per axis audited against the real toolpath, with per-axis direction signs, mirror/invert options, nose-tail reversal and safety stoppers clamping travel at the ends.

Ten post-processor presets

Sealed posts for the machine families above — plus custom raw ISO. Controller-level control: tool-change command (M0 manual or M6 T# for ATCs), dual-spindle select, one-file-per-tool, line numbers, precision digits, and header/footer templates.

The calibration wizard

Cut a calibration square in scrap, measure X/Y from both directions, and the per-machine scale and backlash compensation is computed and applied at emission — with a re-measure warning above 2%.

Datum & zeros

Eight reference-zero choices (tail stop, nose stop, center, supports, and more) with Z zero at support tops, blank top or spindle home — and a guard that refuses a program emitted on the wrong side of Z0.

Air cut

One toggle lifts the entire program by an air-cut height and runs it at rapid — and stamps an unmissable banner into the file so a dry run can never be mistaken for a cut.

Shape3D machine import

Pull machine type, cutters, axis directions, origin and flip offsets, speeds and densities straight from any .s3d/.s3dx board file — APS3000 and AkuShaper files auto-select their post.

04/blanks_&_stock

The blank catalog

Thirty-three stock classes across six regions, with the pouring houses named where verified — ranked not by marketing but by displaced litres of foam waste between blank and design.

Six regions, real houses

Americas: US Blanks, Marko, Fiberglass Hawaii, Walker Foam. Brazil: Teccel Surfblanks. Europe: BayShapers. Australia: Bennett Surfblanks, Burford Blanks, Surfblanks Australia — plus local-pour classes for South Africa, New Zealand, the EU and Brazil.

  • americas
  • brazil
  • europe
  • south africa
  • australia
  • new zealand

Ranked by fit, not by brand

Fits-first ordering by real foam waste, non-fits by smallest shortfall, and a one-step apply of the fit’s offsets. Your region, one filter.

Scan your supplier

Rank your own blank files — CSV, Shape3D, BoardCAD, JSON — by the same fit verdict and waste percentage.

Auto blanks

Generate the blank from the board — allowance per end and per rail, thickness headroom, block-blank mode, auto-fit position and ±15° rocker nesting. An undersized blank is a hard readiness error, full stop.

Material system

One-click feed tables per foam and wood, a shop-editable material database with stringer-cross factors and cost per litre, JSON import/export for sharing between machines and shops.

05/workholding_&_flip

Two sides, one datum

The deck/bottom flip is where boards are lost. ShapeStudio Pro treats it as a measured, verified operation — supports, offsets, and a probe-grade check before side two.

Supports, placed smart

H1/H2 posts with per-post flip offsets — or one button that scores every candidate pair (rigidity sweet spots, plug-pocket keep-outs) and writes the best clear pair with proof lines. Red conflicts the moment a post sits under a pocket.

The flip workflow

Deck-first or bottom-first, second-side support heights, flip offsets in X/Y/Z, re-clamp prompts and tip-clamp options written into the file where the operator needs them.

Flip Verify

A guided wizard that predicts the surface Z at three probe stations, computes the exact machine X to probe — blank offsets, tilt, origin, mirror and flip included — grades each IN or OUT of tolerance, paints the markers on the profile view, and applies the mean deviation to the flip offset in one click.

Setup template DXF

A plan-view bed drawing — envelope, blank contour, board outline, support pads, origin cross — on separate CAD layers in machine millimeters, ready for jig, vacuum plate or shim design.

06/engraving

Signature Studio

Draw it once — with finger, stylus or mouse — and the machine writes it in the foam beside the stringer, at a depth you choose.

Your hand, vectorized

The drawn stroke becomes engrave toolpath — width 3 to 20 cm, depth 0.05 to 0.4 cm — centered on the stringer or out on the foam, on deck, bottom or both.

  • 3–20 cm
  • 0.05–0.4 cm deep

The shop signature library

Save, load and delete named signatures — the house signature is an asset, not a habit.

Two ways into the program

Embedded in the stringer operation (same tool, same block) or as its own trailing ENGRAVE operation behind a real tool change with a dedicated engrave bit.

Confirmed, then cut

Applying a signature confirms with the real number of machine moves it adds — and the Run tab shows the armed state and face at a glance.

07/shop_floor

The production suite

Every export carries a manifest of the job it belongs to — so the setup sheet, the quote, the queue and the operator screen all describe the same cut with the same clock.

Setup sheet

Print or PDF: board and blank dims, origin and offsets, workholding, speeds, the tools table and the operation schedule with times — plus a .job.json sidecar manifest on every export.

Quotes that cost real things

Material + machine + labor + tooling, your margin — priced from the same manifest that drives the machine, with a persisted log of 200 quotes and CSV export.

Compare to last cut

A full CNC-settings diff against any of the last fifty exports, grouped by tab, old values struck through in red. Nothing changes silently.

The job queue

Batch many boards and sides; it persists across restarts, re-derives G-code from the source documents so a toolpath can never go stale, and flags settings drift per job.

Operator Mode

A full-screen tablet overlay for the shop floor: giant job identity, an operation checklist with mark-done, and live progress bound to playback — working from the sidecar weeks later.

Resume interrupted jobs

Pick the operation and pass the machine died on; the re-export covers only the remaining work behind an unmissable recovery header — re-clamp, re-touch-off, verify tool — and lists any settings drift since the original cut.

Tool life

Cutters shared across documents with lifetime accrued in millimeters on every export — and a pre-export warning naming the tool, the millimeters short, and the operation where it would die.

As-cut audit

Probe a grid over the cut face — or paste a probe log — and a plane fit separates datum error, bed tilt in mm/m along and across, and local defect RMS. One click writes the Z compensation.

Download

Free to start. Shape tonight.

ShapeStudio Light is the one public download — the full design studio, free forever: no key, no account, boards never expire. Buy Design or Pro above and your license key plus a private download link for that edition arrive by email.

latest · v0.8.0

ShapeStudio Light

free · design studio

No key needed — free forever. Need exports or CNC? Buy Design or Pro above — your license key and private download link arrive by email.

Release notes & every past Light build on GitHub releases — no telemetry, no account, your boards stay yours.